My new, waterproof models

Répondre
Avatar de l’utilisateur
Arthor
Messages : 3
Inscription : 08 juin 2016, 14:58

My new, waterproof models

Message non lu par Arthor » 26 sept. 2018, 00:01

Hi,
it's been a while since I wrote here last time. Meanwhile I have built few models. Let me present them ;-)

Flying wing FPV49 Penguin scaled 2x down (Originally it has 1250 cm wingspan, mine had 625cm).

Image Image

Unfortunately, when I decided to fly over the sea, He decided to go to swim :,-( It was his last flight...

Image Image

Since then, I decided that all my future models will be waterproof. So...:

Polystyrene throwing toy transformed into "motoglider". Flight time 6-13 minutes. Not too much, but I was able to fly 1,2km away and return :-)

Image Image
https://www.youtube.com/watch?v=-lVCN6NEmq4

After some time I added floats under wings. It shows, that this plane can easily land on the water. When I tried to start, it transformed into submarine... ;-) But it still works.
Image

Beholder - fiberglass boat for filming underwater...

Image Image

More photos and building progress you can find here: http://rc-fpv.pl/viewtopic.php?f=29&t=43121

Waterproof flying wing with RDS - FPV49 Seagull:

Image Image Image Image

More photos here: http://rc-fpv.pl/viewtopic.php?f=26&t=45132
The problem with polystyrene planes is thermal isolation and camera overheating. GoPro turns off after 10 minutes of flight. I've already ordered Peltier cooling plate, heat sink and miniature fan and I will install active cooling for camera.
By the way, it flies like a charm. This flying wing is amazing... :-)

Right now I'm working on flying wing made of Kevlar. It will be plane based on chineese Sonicmodel F1. I've already made two forms for upper and lower part of plane. In next few months I hope to make this plane. It will be possible to use classic motor with propeller or EDF turbine. I hope to reach 200km/h... :-D

Avatar de l’utilisateur
Uncle Jim
Messages : 648
Inscription : 10 mai 2018, 18:55

Re: My new, waterproof models

Message non lu par Uncle Jim » 26 sept. 2018, 13:16

Bonjour Arthor, et bienvenue sur le forum,

Après avoir visionné les liens que tu proposes dans ton post, j'en conclus que tu es aéromodéliste, que tu es basé dans la région de Perpignan, et que tu interviens sur d'autres forums dans une langue d'un pays d'Europe de l'Est. Je suppose que tu écris en Anglais sur ce forum local car tu ne maitrises pas bien le Français.
Les photos me font penser que tes modèles ont quelque chose à voir avec l'eau, aussi je te propose de venir nous voir le 6 ou le 7 Octobre au lac du Salagou (Détails sur le site de l'AMVH). Nous t'y recevrons avec plaisir.
A bientôt j'espère. Cordialement,

UJ.
Penser c'est résister à l'invasion de l'esprit par le rien.

Avatar de l’utilisateur
Arthor
Messages : 3
Inscription : 08 juin 2016, 14:58

Re: My new, waterproof models

Message non lu par Arthor » 26 sept. 2018, 21:51

Merci pour ta reponse,
Je suis origine Polonaise et j'habite a la France depuis 3,5 ans. Quand je me suis inscrit a cette forum, j'ai vecu a Lodeve, mais pas long temp aupres je demenage a Perpignan.
Mon premiere avion a fini sa vie dans la mer. Aupres ca je decide que tous mes prochaine models seront l'eau resistant.
Recontre a Lac Salagou est interessante, mais je n'ai ni licence ni assurance. Est-ce un problème? L'assurance est-elle obligatoire pour faire voler en France?

Je suis desole pour mon francaise :)

Répondre

Revenir à « NOS MODELES »